Hi,

I got a problem with the B772 with the GE engines and the Worldlinerrs mod.

When im in flight and maintaining an Altitude and a low airspeed the Aircraft has to pitch up about 10 degrees to maintain its altitude.

Does anyone know ho to fix this?

right, the Situation is Not Realistic  at all, but the Problem also shows up at Short final.
The Aircrafts Pitch is again at is at about 10 degrees with Full Flips extended, a normal landing Speed and a normal landing weight, while the Fpv is on the horizon.
When i pitch down to about 2 degrees i get a descend rate of -2000fpm, which i dont think is normal

Thank you for your fast answer,

I dont have the exact weights, cause im not at Home, but i can tell you that i had about 5% of fuel left on landing and no extra weight( Passengers or Cargo onboard). I will try to recreate that Flight to give you the exact Numbers .

Yes, im using the WorldlinerRs Mod 1.3.2

My airspeed at Final Approach was 140kt with 000/0 Wind

L r N wrote on Apr 21^st, 2023 at 7:21am:


I found a fix that makes the three Com frequency displays display properly. USE AT YOUR OWN RISK. 

This fix works loading the aircraft at the gate or ramp.  No need to press Cntrl-E.  It works for me, and it may work for you.  If not, or these changes cause other problems, you can just restore the unmodified files.   

On my setup, the frequencies are all visible and swapping the standby frequency for the active frequency on each of the three com channels works.

You need to have the files contained in wlrs-captainsim-boeing_XoPct_CS1.3.2.zip (Salty)installed in your community folder (you don't need the ones for aircraft you don't have installed).  The link is available at the beginning of this thread.

I have the 777-200ER GE and 777-300ER (GE engines) purchased from this site.  I don't own other versions but this fix might work for them too.

FOR THE 777-200ER GE:
   
Start in the folder:
wlrs-captainsim-boeing_XoPct_CS1.3.2\wlrs-captainsim-b772-ge90\SimObjects\Airpla
nes\CS_B777-200ER_GE90B

The two files you need to modify can be edited with Notepad.
FIRST, MAKE A BACKUP OF Apron.flt by copying it to a safe place outside the community folder.

Open Apron.flt with Notepad.

Find the section [Avionics.0]
 
The first entry under this heading is:
Comm1Active=122.800

The last entry is:
AvionicsSwitch=False

Delete the ENTIRE SECTION., from the [Avionics.0] entry all the way down to AvionicsSwitch=False

Save the file.  Make sure the saved file has the same name and stil ends in .flt

SECOND, in the same folder, locate the subfolder Model and open it.

MAKE A BACKUP OF m772_201_interior.xml by copying it to a safe place outside the community folder.

Open m772_201_interior.xml with Notepad.

Search for
  B777_Com
(You will find three entries, one for each Com panel, each in a line that looks like this:
  <PANEL_NAME>B777_Com</PANEL_NAME>)

Carefully change "B777_Com" to "B747_8_Com" (without the quotes).

Be careful not to make any other changes; even an extra  ".  "," or ";" can mess up the entire file.  That's why you need a backup.

Save the file.  Make sure the saved file has the same name and still ends in .xml.

MODIFYING THE 777-300ER the folder to edit is:
wlrs-captainsim-boeing_XoPct_CS1.3.2\wlrs-captainsim-b77w-ge90\SimObjects\Airpla
nes\CS_B777-300ER_GE115B

The apron.flt file has the same name, and the model folder file name is m773_305_interior.xml)

SOMETIMES THE COM FREQUENCY DISPLAYS GO BLANK IN THE MIDDLE OF THE FLIGHT.  CONTROL-E FIXES THIS FOR ME, and since the engines are already running and everything else is already turned on, it doesn't cause any problems.