(UTC)
  Visit Captain Sim web site  
  Welcome, Guest. Please Login or Register

  

  CAPTAIN SIM FORUM › 757 Captain III › 757 Captain III - General › CTD w/ Cold & Dark.cfg
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
CTD w/ Cold & Dark.cfg (Read 810 times)
Coqui297
Full Member
*
Offline



Posts: 37
Location: Ocala, Florida �USA
Joined: Mar 1st, 2006
Gender: Male
CTD w/ Cold & Dark.cfg
Feb 9th, 2019 at 8:17pm
Print Post  
If I use the Cold and Dark setting by changing the Cold & Dark cfg name to default.cfg in the Custom folder after a few minutes in the air the plane just CTD. Tried twice and is the same outcome . Huh
  

Carlos F. Rodriguez/ KOCF
Back to top
 
IP Logged
 
Markoz
CS Team
*
Offline



Posts: 12360
Location: Victoria, Australia
Joined: Apr 24th, 2009
Gender: Male
Re: CTD w/ Cold & Dark.cfg
Reply #1 - Feb 10th, 2019 at 2:01am
Print Post  
1) Load the COLD AND DARK setting from BASIC STATES
2) The Battery (BAT) Switch will already be ON, so rotate the Standby (STBY) POWER Selector to AUTO
3) Save the new state as DEFAULT in the CUSTOM STATES.

I know this isn't a true Cold and Dark setting, but it's the closest I can get to it because I can't find as way to access the CDU's menu, without first turning the Standby (STBY) POWER Selector to AUTO, or BAT. I looked through the DEFAULT.cfg that I created doing the above, but I can't find (or figure out) the entry that is the Standby (STBY) POWER Selector in it. I assumed it would be listed under O07, because of this - O07. BATTERY/STANDBY CONTROL PANEL (from the CS757CAPTAINIII_MANUAL_PART2.pdf), but I can only find 3 entries, and they all matched in the COLD AND DARK.cfg, and the DEFAULT.cfg files  Sad
  
Mark Fletcher



PC: i7 10700K @3.8/5.1GHz | 64GB DDR4 3200 | 12GB RTX 4070 Super | 32" LCD Monitor | 1TB SSD & 2x2TB SSD | Win 11 Pro - FSX/FSX-SE/P3D3/P3D4/P3D5/P3D6/MSFS2020
15.6" Gaming Laptop: i7 7700HQ | 32GB DDR4 | 6GB GTX 1060 | 256GB SSD & 1TB HDD | Win 10 Pro 64bit - FSX-SE/P3D4
Back to top
 
IP Logged
 
Colvale
Senior Member
*
Offline



Posts: 253
Joined: Jun 23rd, 2011
Gender: Male
Re: CTD w/ Cold & Dark.cfg
Reply #2 - Feb 10th, 2019 at 9:07am
Print Post  
Markoz wrote on Feb 10th, 2019 at 2:01am:
1) Load the COLD AND DARK setting from BASIC STATES
2) The Battery (BAT) Switch will already be ON, so rotate the Standby (STBY) POWER Selector to AUTO
3) Save the new state as DEFAULT in the CUSTOM STATES.

I know this isn't a true Cold and Dark setting, but it's the closest I can get to it because I can't find as way to access the CDU's menu, without first turning the Standby (STBY) POWER Selector to AUTO, or BAT. I looked through the DEFAULT.cfg that I created doing the above, but I can't find (or figure out) the entry that is the Standby (STBY) POWER Selector in it. I assumed it would be listed under O07, because of this - O07. BATTERY/STANDBY CONTROL PANEL (from the CS757CAPTAINIII_MANUAL_PART2.pdf), but I can only find 3 entries, and they all matched in the COLD AND DARK.cfg, and the DEFAULT.cfg files  Sad


Precisely the way I have done it and now have C&D every single time.
  
C+D_from_Menu.JPG ( 234 KB | 94 Downloads )
C+D_from_Menu.JPG
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board  ^Top   

CAPTAIN SIM FORUM » Powered by YaBB 2.6.0!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge