Quote:The problem is that firstly I do not get the GSX stairs on any of the 737's. This is okay to a point because you have the air stairs, but for a bit of added realism, especially as I fly it a lot in South Africa, where not all our airports have jetways and use the old fashioned stairs it is nice.
Create a gsx.cfg in the
FSX\SimObjects\Airplanes\CS_B737-200 folder. Copy and paste this:
[aircraft]
nosegear = 9.14
refueling = 1
[exit1]
pos = -1.66 7.97 -0.52 5.60
code = 1
name = Main Passenger Door
[exit2]
pos = -1.43 -10.40 -0.51 -11.70
code = (L:PassDoor2,bool)
name = Aft Passenger Door
[exit3]
remove = 1
[exit4]
remove = 1
[service1]
pos = 1.56 8.21 -0.52 -7.10
code = (L:ServDoor1,bool)
name = Forward Service Door
[service2]
pos = 1.34 -10.44 -0.54 10.20
code = (L:ServDoor2,bool)
name = Aft Service Door
[cargo1]
pos = 0.84 4.41 -1.84 0.90
code = 3
name = Forward Cargo Door
uldcode = AUTO
[cargo2]
pos = 0.88 -6.67 -1.80 9.30
code = 4
name = Aft Cargo Door
uldcode = AUTO
and see if that works. That works for me, so it should for you too.
Quote:The other thing is that on my 200 and the Adv the bagage loaders do not come up, yet on the C and F, they do. The same for catering. All seems a bit reversed.
There are no baggage loaders for the -200ADV, only for the -200C/F. The above code works for the -200ADV as well.
Here is the gsx.cfg code for the -200C:
[aircraft]
nosegear = 9.144
refueling = 1
absoluteheights = 0
[exit1]
pos = -1.65 7.9 -0.762 7.0
code = 1
name = Forward Passenger Door
[exit2]
pos = -1.38 -10.4 -0.15 -12.0
code = 1
name = Rear Passenger Door
[exit3]
remove = 1
[exit4]
remove = 1
[service1]
pos = 1.38 -10.25 -0.15 12.0
code = 0
[service2]
remove = 1
[cargo1]
pos = 1.524 3.972 -1.9 0.0
code = 3
name = Forward Cargo Door
uldcode = BELT
[cargo2]
pos = 1.158 -6.7 -1.44 0.0
code = 4
name = Rear Cargo Door
uldcode = BELT
and for the -200F:
[aircraft]
nosegear = 9.144
refueling = 1
absoluteheights = 0
[exit1]
pos = -1.65 7.9 -0.762 7.0
code = 1
name = Forward Passenger Door
[exit2]
remove = 1
[exit3]
remove = 1
[exit4]
remove = 1
[service1]
pos = 1.65 8.15 -0.762 -7.0
code = 0
[service2]
remove = 1
[cargo1]
pos = 1.524 3.972 -1.9 0.0
code = 3
name = Forward Cargo Door
uldcode = BELT
[cargo2]
pos = 1.158 -6.7 -1.44 0.0
code = 4
name = Rear Cargo Door
uldcode = BELT
Hope this helps.
Edited: Looking at the codes for the 737-200C/F, it looks like they are the older ones I have. I'll look for the newer ones which I think are done better than that, but I might just have to redo them. Let me know how those last two (for the -200C and -200F) work. Please.