CAPTAIN SIM FORUM | |
1011 Captain II >> 1011 Captain II - General >> How do I get to the "Ready to Start" selection?
https://www.captainsim.org/forum/csf.pl?num=1614278887 Message started by Wings of Gold on Feb 25th, 2021 at 6:48pm |
Title: How do I get to the "Ready to Start" selection? Post by Wings of Gold on Feb 25th, 2021 at 6:48pm
I normally select any aircraft for P3DV4 by typing it's title line into the "Change vehicle\search" line. My L-10011 will then appear at the desired airport with it's engines winding down. I want to select "Ready for take-off (twice)" at this point - but I can't figure out where to make that selection. Advice please.
Bill |
Title: Re: How do I get to the "Ready to Start" selection? Post by Markoz on Feb 26th, 2021 at 12:48am
Menu > Add-ons > CS 1011 Captain II > Panel State: Load > Select Ready for takeoff from the list in the box that opens. Repeat once (I have to do it twice for the engines to remain running).
If you want a Ready to start option, you need to get the L-1011 to that point, then save the panel: 1. Go to P3Dv4\Captain_Sim\1011 II\panel and backup the DEFAULT.cfg to DEFAULT-BAK-cfg 2. In P3Dv4 with the L-1011 in a "Ready to Start" setting, Menu > Add-ons > CS 1011 Captain II > Panel State: Save Current As > Save it by clicking on DEFAULT 3. Go to P3Dv4\Captain_Sim\1011 II\panel and rename the DEFAULT.cfg to READY TO START.cfg 4. Rename the backed up DEFAULT-BAK.CFG to DEFAULT.cfg |
Title: Re: How do I get to the "Ready to Start" selection? Post by Wings of Gold on Feb 26th, 2021 at 5:20pm
Hi Markoz, That you Very Much for your response. Please see my PM.
Bill (Wings of Gold) |
Title: Re: How do I get to the "Ready to Start" selection? Post by Markoz on Feb 27th, 2021 at 1:25am
I have replied to your PM, but I will just reiterate what it says (so everyone else can know). I believe you have the 1011 Captain for FSX/SE/P3D3, and not the 1011 Captain II for P3D4/P3D5.
|
Title: Re: How do I get to the "Ready to Start" selection? Post by Wings of Gold on Mar 3rd, 2021 at 6:30pm
Hi Mark, The store shows that I have the P3D version. I have deleted the version we have been discussing and downloaded a new one (it IS the P3D version) and selected and installed it in P3Dv4. Now - how do I select "Ready for start". I can find no information on setup in the manual. Regards, Bill
|
Title: Re: How do I get to the "Ready to Start" selection? Post by Wings of Gold on Mar 3rd, 2021 at 6:33pm
Meant to say it is the Captain II base Pack (P3D4/5)
Bill |
Title: Re: How do I get to the "Ready to Start" selection? Post by Markoz on Mar 4th, 2021 at 4:00am Wings of Gold wrote on Mar 3rd, 2021 at 6:30pm:
I answered that here: Markoz wrote on Feb 26th, 2021 at 12:48am:
Wings of Gold wrote on Mar 3rd, 2021 at 6:30pm:
I don't think it tells you in the manual (I'll ask for that to be changed). I would upload an image, but P3Dv4 shuts down every time I select the L-1011 on my laptop (PC is out of action due to the power supply carking it ). |
Title: Re: How do I get to the "Ready to Start" selection? Post by Wings of Gold on Mar 10th, 2021 at 4:40pm
Hi Mark,
My CS 1011 Captain II never appears in the (upper toolbar) Add-ons column (no matter how long I wait) Bill |
CAPTAIN SIM FORUM » Powered by YaBB 2.6.0! YaBB Forum Software © 2000-2024. All Rights Reserved. |