The jetway does not line up with the passenger door. It goes to the middle of the plane. Anyone else have this issue? Is this a fix that Captain Sim needs to fix in the Modeling config or is it adjustable in the aircraft config?  

It would be nice to have the jetway actually go to the front passenger door when you pull up to a terminal gate!

Sorry if this has been covered before. I tried search and nothing came up.

Scroll back in this forum. Someone came up with a fix already.

Please, take a look at http://www.captainsim.org/yabb2/YaBB.pl?num=1335018713/

Pinatubo wrote on Jun 1^st, 2012 at 11:21pm:

Please, take a look at http://www.captainsim.org/yabb2/YaBB.pl?num=1335018713/

Awesome! Thank you, I'll give it a try. You gotta love forums!  :)

Firecapt_32 wrote on Jun 1^st, 2012 at 11:19pm:

Scroll back in this forum. Someone came up with a fix already.

That fix didn't work for me! :(

I plan on sorting it out, but have not done so yet. Seeing as I use GSX, which I have already got that set up nearly perfectly, it has not been a high priority for sorting out the door locations.

Hi all,

I have had the same problems and managed to get it fixed to an acceptable level for the main exit (default FSX jetway)
Regarding the Cargo doors, I have not yet been able to fix the cargo contact points properly yet, everytime I change it in a logical way, unlogical things seem to happen. I haven't been able to figure it out yet.

For the 737-100 I am using
[exits]
number_of_exits = 4
exit.0 = 0.4, 23.3, -5.6, 1.0, 0
exit.1 = 10.0, 17.3, 5.5, 4.0, 2
exit.2 = 0.4, 0.0, 5.0, -3.0, 1
exit.3 = 0.4, 0.0, 5.0, -3.7, 1

For the 737-200 I am using:
[exits]
number_of_exits = 4
exit.0 = 0.4, 26.3, -5.6, 1.0, 0
exit.1 = 10.0,  20.3,  5.6,  4.0, 2
exit.2 =  0.4,  13.0,  5.0, -3.0, 1
exit.3 =  0.4, -22.0,  3.8, -3.7, 1

For the 737-200ADV I am using:
[exits]
number_of_exits = 4
exit.0 = 0.4, 26.3, -5.6, 1.0, 0
exit.1 = 10.0,  38.0,  0.0,  4.0, 2
exit.2 =  0.4,  13.0,  5.0, -3.0, 1
exit.3 =  0.4, -22.0,  3.8, -3.7, 1

For the 737-200C I am using:
[exits]
number_of_exits = 4
exit.0 = 0.4, 26.3, -5.6, 1.0, 0
exit.1 = 10.0,  38.0,  0.0,  4.0, 2
exit.2 =  0.4,  13.0,  5.0, -3.0, 1
exit.3 =  0.4, -22.0,  3.8, -3.7, 1

For the 737-200F I am using:
[exits]
number_of_exits = 4
exit.0 = 0.4, 26.3, -5.6, 1.0, 0
exit.1 = 10.0,  38.0,  0.0,  4.0, 2
exit.2 =  0.4,  13.0,  5.0, -3.0, 1
exit.3 =  0.4, -22.0,  3.8, -3.7, 1

You will actually only have to change the first line for the Exits section i.e. 'exit.0' in the aircraft.cfg file for each model

Hope this helps.

Best Regards,
Marc